Huawei eSpace 7910

From Bicom Systems Wiki

Introduction

Huawei eSpace 7910 User Guide

This Configuration Guide is written as general guide on how to configure the Huawei phone model eSpace 7910 to work with PBXware 4.1.

Requirements

Identifying phone model

To start and successfully complete registration of your Huawei phone you need to know which phone model you will setup.

On the front of each Huawei phone there are exact model information that you should check. Although different phone models can have exactly the same requirements and installation procedure, phone models can also have significantly different requirements and installation procedure, so that ignorance of your own model may result in the inability to successfully set up your phone.

Phone firmware

  • Make sure that your phone is loaded with appropriate firmware version, xxxSPCh00.
  • To find out the firmware version of your Huawei phone model open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: http://192.168.1.22.
  • Login to phone web administration interface with your username and password. Please note, factory default login details are username: admin and password: admin123.

DHCP server

Fully configured and operational DHCP server.

PBXware version

PBXware version 4.1

In order to find out the PBXware version:

  • Login to PBXware
  • Navigate to Settings: About.

On the top of About page is a code similar to this one PBXware Edition: Business, Release: 4.1 (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v4.1 (62b7bcd), API: 4.1, libmemcached version: 1.0.14, where Release denotes the exact version of your PBXware.

Installation

This chapter describes how to install and connect the phone to the electrical power and data network as well as how to apply factory settings.

The following topics are covered:

  • Power adapter
  • Power over Ethernet (PoE)
  • Factory Settings

Power adapter

Connect the Network and Power

  • Connect the DC plug on the power adapter to the DC port on the phone and connect the other end of the power adapter into an electrical power outlet.
  • Connect the ethernet cable between the Internet port on the phone and the network port on a router or switch to access LAN.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Power over Ethernet (PoE)

Connect the Network (only)

Using a regular ethernet cable, your phone can be powered from a Power over Ethernet (PoE) compliant router or switch.

  • Connect the Ethernet cable between the Internet port on the phone and an available port on the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Find the phone IP address

Find out your Huawei phone IP Address.

  • Press the Home button.
  • Go to Apps menu.
  • Go to Status menu.
  • Go to Network menu.

The IP address will be displayed on the top of display.

Reset to factory settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been already used then it is a must.

  • Open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: http://192.168.1.22.
  • Login to phone web administration interface with your username and password. Please note, factory default login details are username: admin and password: admin123.
  • Click on Advanced on the left navigation menu.
  • Click on Factory reset submenu.
  • Click on Factory reset button and confirm in order to reset the phone to factory settings. Phone will be reset to the factory settings and reboot.
  • Wait sometime prior for device to reboot.

NOTE: Do not unplug or remove power to the phone while it is updating firmware and configurations.

Registering phone

This chapter describes how to identify Huawei phone model, requirements that must be met and how to register the phone using manual configuration or auto provisioning.

The following topics are covered:

  • Manual configuration
  • Auto provisioning

Manual configuration

This chapter describes how to set UAD settings, create PBXware extension and register the phone.

The following topics are covered:

  • UAD settings
  • Creating extension
  • Registering phone

UAD Settings

UAD settings

Login to PBXware web administration interface

  • Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: http://192.168.1.10.
  • Login to PBXware with your e-mail address and password.

UAD settings

  • Navigate to Settings:UAD.
  • Make sure Huawei UAD is enabled. To check the UAD status click on the edit icon corresponding to your Huawei phone.
  • Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.
  • Click on the Save button to save changes.

Creating extension

Creating Extension

Add Extension

  • Navigate to Extensions. Click on Add Extension.
  • The standard options window will be shown below.
  • Select Huawei phone model from the UAD select box.
  • Select Location: Local or Remote.
Local is for all extensions registered on the LAN and Remote is for all extensions registered from remote networks, WAN, Internet etc.
  • Click on the Next step button.

Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

  • Name
Enter a name for the extension being created. Example: John Smith.
  • E-mail
Enter the e-mail address associated with this extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com
  • Department
Department to which extension will belong to. Example: Sales.
  • Click on the Save button.

Registering Phone

This chapter describes how to register Huawei phone using Hostname or IP Address.

Hostname or IP Address

Login to phone web administration interface

  • Open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: http://192.168.1.22
  • Login to phone web administration interface with your username and password. Please note, factory default login details are username: admin and password: admin123.
  • Click on Advanced and select Account submenu.
  • Click on Add account
  • Enter or set the following details into the respective fields.
REQUIRED FIELDS:
  • Account
PBXware extension number. Example: 1003
  • Password
The Secret of the extension as received in the e-mail associated with this extension. Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created extension.
  • User Name
Usually the same number as the Account.
  • Label Name
Usually the same number as the Account.
  • Sip Server 1
Enter the Hostname or IP Address of the PBXware.
- Example for Hostname: voip.bicomsystems.com
- Example for IP Address: 192.168.1.10
  • Click on the Ok button.
  • Click on the Save button.
  • You'll have to wait sometime prior for the device to register. If everything is done as above described, you should have successfully registered your phone to PBXware. Dial *123 to verify registration.

Auto Provisioning

This chapter describes how to set UAD settings, create PBXware extension and register the phone using DHCP or Static IP address.

The following topics are covered:

  • UAD Settings
  • Creating Extension
  • Registering Phone

UAD Settings

UAD settings

Login to PBXware web administration interface.

  • Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: http://192.168.1.10.
  • Login to PBXware with your e-mail address and password.

UAD settings.

  • Navigate to Settings:UAD.
  • Make sure Huawei UAD is enabled. To check the UAD status click on the edit icon corresponding to your Huawei phone.
  • Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
  • Click on the Save button to save changes.

Creating Extension

Creating Extension

Add Extension

  • Navigate to Extensions. Click on Add Extension.
  • The standard options window will be shown below.
  • Select Huawei phone model from the UAD select box.
  • Select Location: Local or Remote.
Local is for all extensions registered on the LAN and Remote is for all extensions registered from remote networks, WAN, Internet etc.
  • Click on the Next step button.

Extension values

Enter values into the required field text boxes.
REQUIRED FIELDS:
  • Name
Enter a name for the extension being created. Example: John Smith.
  • E-mail
Enter the e-mail address associated with this extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com
  • Auto Provisioning
Set to Yes.
  • MAC Address
Enter Huawei phone MAC address. Example: 20F17C123456. MAC address can be found at the back of the phone.
  • Click on the Save button.

Registering Phone

This chapter describes how to register Huawei phone using DHCP.

DHCP

Configure DHCP

  • Make sure your DHCP router is configured to use option 246 to automatically instruct phones with the URL for auto provisioning. For more information refer to your router documentation or contact your network administrator.

Phone first boot or user initiated reboot

  • Auto provisioning process will start during phone first boot or after reboot process has been initiated by user. DHCP server will instruct the phone where from to pickup appropriate configuration file. If everything is done as above described, you should have successfully registered your phone to PBXware. Dial *123 to verify registration.