Difference between revisions of "Gigaset N870"
From Bicom Systems Wiki
(→Introduction) |
(→HTTP) |
||
| (27 intermediate revisions by one user not shown) | |||
| Line 7: | Line 7: | ||
=Requirements= | =Requirements= | ||
| − | ==Identifying | + | ==Identifying Phone Model== |
| − | To start and successfully complete registration of your Gigaset phone you need to know which phone model | + | To start and successfully complete registration of your Gigaset phone you need to know which phone model to set up. |
| − | + | On the back of each Gigaset phone, there is model information that you should check. Although various phone models can have exactly the same requirements and installation procedures, phone models can also have significantly different requirements and installation procedures, so that is why it is important to know the model you own which results in you setting up the device successfully. | |
| − | ==Phone | + | ==Phone Firmware== |
| − | *Make sure that your phone is loaded with appropriate firmware version, <span style="color: red;">2.26.0</span>. | + | *Make sure that your phone is loaded with an appropriate firmware version, <span style="color: red;">2.26.0</span>. |
| − | *To find out the firmware version of your Gigaset phone model open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: '''http://192.168.1.22'''. | + | *To find out the firmware version of your Gigaset phone model, open a new browser window and enter your phone IP address in order to access the phone's web administration interface login screen. Example: '''http://192.168.1.22'''. |
| − | * | + | *Log in to the phone's web administration interface with your username and password. Please note that the factory default username is '''admin''' and the factory default login password is '''admin'''. |
| − | ==DHCP | + | ==DHCP Server== |
Fully configured and operational DHCP server. | Fully configured and operational DHCP server. | ||
| − | + | ||
| − | ==PBXware | + | ==PBXware Version== |
PBXware version <font color="red">5.3.5.0</font> | PBXware version <font color="red">5.3.5.0</font> | ||
| Line 31: | Line 31: | ||
In order to find out the PBXware version: | In order to find out the PBXware version: | ||
| − | * | + | *Log in to PBXware |
*Navigate to '''Settings: About'''. | *Navigate to '''Settings: About'''. | ||
| − | On the top of '''About''' page is a code similar to this one '''PBXware Edition: Business, Release: <font color="red">5.3.5.0</font> (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v5.0 (62b7bcd), API: 5, libmemcached version: 1.0.18,''' where Release denotes the | + | On the top of '''About''' page is a code similar to this one '''PBXware Edition: Business, Release: <font color="red">5.3.5.0</font> (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v5.0 (62b7bcd), API: 5, libmemcached version: 1.0.18,''' where Release denotes the current version of your PBXware. |
| − | =Installation= | + | =Installation= |
| − | This | + | This section describes how to install and connect the phone to the electrical power and data network as well as how to apply factory settings. |
The following topics are covered: | The following topics are covered: | ||
| − | *Power | + | *Power Adapter |
*Power over Ethernet (PoE) | *Power over Ethernet (PoE) | ||
*Factory Settings | *Factory Settings | ||
| − | ==Power | + | ==Power Adapter== |
Connect the Network and Power | Connect the Network and Power | ||
| Line 53: | Line 53: | ||
*Connect the DC plug on the power adapter to the DC port on the phone and connect the other end of the power adapter into an electrical power outlet. | *Connect the DC plug on the power adapter to the DC port on the phone and connect the other end of the power adapter into an electrical power outlet. | ||
| − | *Connect the | + | *Connect the Ethernet cable between the Internet port on the phone and the network port on a router or switch to access LAN. |
<span style="color: red;">'' '''NOTE:''' ''</span> ''If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant''. | <span style="color: red;">'' '''NOTE:''' ''</span> ''If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant''. | ||
| Line 60: | Line 60: | ||
Connect the Network (only) | Connect the Network (only) | ||
| − | Using a regular | + | Using a regular Ethernet cable, your phone can be powered from a Power over Ethernet (PoE) compliant router or switch. |
*Connect the Ethernet cable between the Internet port on the phone and an available port on the in-line power router or switch. | *Connect the Ethernet cable between the Internet port on the phone and an available port on the in-line power router or switch. | ||
| − | <span style="color: red;">'' '''NOTE:''' ''</span> ''If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant''. | + | <span style="color: red;">'' '''NOTE:''' ''</span> ''If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant''. |
| − | ==Find the | + | ==Find the Phone's IP address== |
| − | Find out your Gigaset phone IP Address | + | Find out your Gigaset phone IP Address |
* Open '''Menu''' on a dect phone | * Open '''Menu''' on a dect phone | ||
| Line 77: | Line 77: | ||
* Go to '''Local network''' | * Go to '''Local network''' | ||
| − | IP address should be displayed on the phone. | + | IP address should be displayed on the phone. |
| − | ==Reset to | + | ==Reset to Factory Settings== |
This step is not required for brand new out-of-the-box phones, however, if the phone has been already used then it is a must. | This step is not required for brand new out-of-the-box phones, however, if the phone has been already used then it is a must. | ||
| Line 85: | Line 85: | ||
*Disconnect the power supply. | *Disconnect the power supply. | ||
| − | *Power on the device while keeping the '''Connect''' button pressed and wait 15 seconds until the '''Connect''' button | + | *Power on the device while keeping the '''Connect''' button pressed and wait 15 seconds until the '''Connect''' button starts to blink fast. |
| + | |||
| + | *Release the '''Connect''' button and power off the device. | ||
| − | * | + | *Turn the device on again. |
| − | *Wait | + | *Wait some time for a device to boot. |
<span style="color: red;">'' '''NOTE:''' ''</span> ''Do not unplug or remove power to the phone while it is updating firmware and configuration''. | <span style="color: red;">'' '''NOTE:''' ''</span> ''Do not unplug or remove power to the phone while it is updating firmware and configuration''. | ||
| − | =Registering | + | =Registering Phone= |
| − | This | + | This section describes how to identify Gigaset phone model, requirements that must be met and how to register the phone by using Manual configuration or Auto provisioning. |
The following topics are covered: | The following topics are covered: | ||
| − | *Manual | + | *Manual Configuration |
| − | *Auto | + | *Auto Provisioning |
| − | ==Manual | + | ==Manual Configuration== |
| − | This | + | This section describes how to set UAD settings, create the PBXware extension and register the phone. |
The following topics are covered: | The following topics are covered: | ||
| Line 111: | Line 113: | ||
*UAD settings | *UAD settings | ||
| − | *Creating | + | *Creating Extension |
| − | *Registering | + | *Registering Phone |
===UAD Settings=== | ===UAD Settings=== | ||
| − | [[image: | + | [[image:noautoprov.device.grandstreamgrp.png|thumb|UAD settings]] |
| − | + | Log in to the PBXware's web administration interface | |
*Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: '''http://192.168.1.10.''' | *Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: '''http://192.168.1.10.''' | ||
| − | * | + | *Log in to PBXware with your e-mail address and password. |
| − | UAD | + | UAD Settings |
| − | *Navigate to '''Settings:UAD'''. | + | *Navigate to '''Settings: UAD'''. |
| − | *Make sure | + | *Make sure that the Grandstream UAD is enabled. To check the UAD status, click the '''Edit''' icon corresponding to your Grandstream phone. |
| − | *Make sure '''Status''' is set to '''Active''', '''Auto provisioning''' is set to '''No''', and '''DHCP''' is set to '''Yes'''. | + | *Make sure that '''Status''' is set to '''Active''', '''Auto provisioning''' is set to '''No''', and '''DHCP''' is set to '''Yes'''. |
| − | *Click | + | *Click the '''Save''' button to save changes. |
| − | ===Creating | + | ===Creating Extension=== |
[[image:extension.1.png|thumb|Creating Extension]] | [[image:extension.1.png|thumb|Creating Extension]] | ||
| − | Add Extension | + | Add the Extension |
| − | *Navigate to '''Extensions'''. Click | + | *Navigate to '''Extensions'''. Click the '''Add Extension''' button. |
*The standard options window will be shown below. | *The standard options window will be shown below. | ||
| − | *Select | + | *Select the Grandstream phone model from the '''UAD''' select box. |
*Select Location: '''Local''' or '''Remote'''. | *Select Location: '''Local''' or '''Remote'''. | ||
| − | :'''Local''' is for all | + | :'''Local''' is for all Extensions registered on the LAN and '''Remote''' is for all Extensions registered from remote networks, WAN, Internet etc. |
| − | *Click | + | *Click the '''Next step''' button. |
| − | + | ||
| − | + | ||
| − | Enter values into the required field text boxes. | + | Extension Values |
| + | |||
| + | :Enter values into the required field text boxes. | ||
| − | <span style="color: red;">'''REQUIRED FIELDS:'''</span> | + | :<span style="color: red;">'''REQUIRED FIELDS:'''</span> |
*'''Name''' | *'''Name''' | ||
| − | :Enter a name for the | + | :Enter a name for the Extension being created. Example: '''John Smith'''. |
*'''E-mail''' | *'''E-mail''' | ||
| − | :Enter the e-mail address associated with this | + | :Enter the e-mail address associated with this Extension. This e-mail address will receive all system notification messages. Example: '''john.smith@bicomsystems.com''' |
*'''Department''' | *'''Department''' | ||
| − | :Department to which | + | :Define the Department to which the Extension belongs to. Example: '''Sales'''. |
| − | *Click | + | *Click the '''Save''' button. |
===Registering Phone=== | ===Registering Phone=== | ||
| − | This | + | This section describes how to register Gigaset phones using '''Hostname or IP Address'''. |
====Hostname or IP Address==== | ====Hostname or IP Address==== | ||
| − | + | Log in to the phone's web administration interface | |
| − | *Open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: http://192.168.1.22 | + | *Open a new browser window and enter your phone IP address in order to access the phone's web administration interface login screen. Example: http://192.168.1.22 |
| − | * | + | *Log in to the phone's web administration interface with your password. Please note that the factory default username is '''admin''' and the factory default login password is '''admin'''. |
| − | *Click | + | *Click the '''Settings''' tab at the top navigation menu. |
| − | *Click | + | *Click '''Telephony''' at the left navigation menu. |
| − | *Click | + | *Click the first '''Edit''' button. |
| − | *Click '''Show advanced settings''' button | + | *Click the '''Show advanced settings''' button. |
*Enter or set the following details into the respective fields. | *Enter or set the following details into the respective fields. | ||
| Line 198: | Line 200: | ||
*'''Authentication name''' | *'''Authentication name''' | ||
| − | :PBXware | + | :PBXware Extension number. Example: '''1003''' |
*'''Authentication password''' | *'''Authentication password''' | ||
| − | :The Secret of the | + | :The Secret of the Extension as received in the e-mail associated with this Extension. Example: '''_%Z4M3*Ts9y7'''. A password is generated automatically for each newly created Extension. |
*'''Username''' | *'''Username''' | ||
| Line 224: | Line 226: | ||
:Same as the '''Domain''' field. | :Same as the '''Domain''' field. | ||
| − | *Click '''Set''' button. | + | *Click the '''Set''' button. |
| − | *You | + | *You will have to wait some time for a device to reboot. If everything is done as described above, you should have successfully registered your phone to PBXware. |
| + | |||
| + | Dial *123 to verify registration. | ||
==Auto Provisioning== | ==Auto Provisioning== | ||
| − | This | + | This section describes how to set UAD settings, create the PBXware Extension, and register the phone using DHCP or Static IP address. |
The following topics are covered: | The following topics are covered: | ||
| Line 240: | Line 244: | ||
*Registering Phone | *Registering Phone | ||
| − | ===UAD Settings=== | + | ==='''UAD Settings'''=== |
| − | [[image: | + | [[image:autoprov.device.grandstreamgrp.png|thumb|UAD settings]] |
| − | + | Log in to the PBXware's web administration interface. | |
| − | + | ||
*Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: '''http://192.168.1.10'''. | *Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: '''http://192.168.1.10'''. | ||
| − | * | + | *Log in to PBXware with your e-mail address and password. |
| − | UAD | + | UAD Settings |
| − | *Navigate to '''Settings:UAD'''. | + | *Navigate to '''Settings: UAD'''. |
| − | *Make sure | + | *Make sure that the Grandstream UAD is enabled. To check the UAD status, click the '''Edit''' icon corresponding to your Grandstream phone. |
| − | *Make sure '''Status''' is set to '''Active''', '''Auto provisioning''' is set to '''Yes''', and '''DHCP''' is set to '''Yes'''. | + | *Make sure that '''Status''' is set to '''Active''', '''Auto provisioning''' is set to '''Yes''', and '''DHCP''' is set to '''Yes'''. |
| − | *Click | + | *Click the '''Save''' button to save changes. |
| − | ===Creating Extension=== | + | ==='''Creating Extension'''=== |
[[image:extension.2.png|thumb|Creating Extension]] | [[image:extension.2.png|thumb|Creating Extension]] | ||
| − | Add Extension | + | Add the Extension |
| − | *Navigate to '''Extensions'''. Click | + | *Navigate to '''Extensions'''. Click the '''Add Extension''' button. |
*The standard options window will be shown below. | *The standard options window will be shown below. | ||
| − | *Select | + | *Select the Grandstream phone model from the '''UAD''' select box. |
*Select Location: '''Local''' or '''Remote'''. | *Select Location: '''Local''' or '''Remote'''. | ||
| − | :'''Local''' is for all | + | :'''Local''' is for all Extensions registered on the LAN and '''Remote''' is for all Extensions registered from remote networks, WAN, Internet etc. |
| − | *Click | + | *Click the '''Next step''' button. |
| − | Extension | + | Extension Values |
:Enter values into the required field text boxes. | :Enter values into the required field text boxes. | ||
| Line 282: | Line 285: | ||
*'''Name''' | *'''Name''' | ||
| − | :Enter a name for the | + | :Enter a name for the Extension being created. Example: '''John Smith'''. |
*'''E-mail''' | *'''E-mail''' | ||
| − | :Enter the e-mail address associated with this | + | :Enter the e-mail address associated with this Extension. This e-mail address will receive all system notification messages. Example: '''john.smith@bicomsystems.com''' |
*'''Auto Provisioning''' | *'''Auto Provisioning''' | ||
| Line 294: | Line 297: | ||
*'''MAC Address''' | *'''MAC Address''' | ||
| − | :Enter Gigaset phone MAC address. Example: '''7C2F80123456'''. MAC address can be found at the back of the phone. | + | :Enter the Gigaset phone's MAC address. Example: '''7C2F80123456'''. The MAC address can be found at the back of the phone. |
| − | *Click | + | *Click the '''Save''' button. |
===Registering Phone=== | ===Registering Phone=== | ||
| − | This | + | This section describes how to register Gigaset phones using '''DHCP''' or '''HTTP'''. |
The following topics are covered: | The following topics are covered: | ||
| Line 312: | Line 315: | ||
Configure DHCP | Configure DHCP | ||
| − | *Make sure your DHCP router is configured to use '''option 66''' to automatically instruct phones with the URL for | + | *Make sure that your DHCP router is configured to use '''option 66''' to automatically instruct phones with the URL for Auto provisioning. For more information, please refer to your router documentation or contact your network administrator. |
| − | Phone first boot or user initiated reboot | + | Phone's first boot or user initiated reboot |
| − | *Auto provisioning process will start during phone first boot or after reboot process has been initiated by user. DHCP server will instruct the phone | + | *The Auto provisioning process will start during the phone's first boot or after the reboot process has been initiated by the user. The DHCP server will instruct the phone from where to pick up an appropriate configuration file. If everything is done as described above, you should have successfully registered your phone to PBXware. |
| + | |||
| + | Dial '''*123''' to verify registration. | ||
====HTTP==== | ====HTTP==== | ||
| Line 322: | Line 327: | ||
*Open a new browser window and enter your phone IP address, e.g. '''http://192.168.1.22'''. | *Open a new browser window and enter your phone IP address, e.g. '''http://192.168.1.22'''. | ||
| − | *Enter '''username''' and '''password''' and press '''Confirm''' button. <font color="red">'''NOTE:'''</font> | + | *Enter '''username''' and '''password''' and press the '''Confirm''' button. <font color="red">'''NOTE:'''</font> The factory default username is '''admin''' and the factory default password is '''admin'''. |
| − | *Click | + | *Click the '''Settings''' tab. |
| − | :*Click | + | :*Click '''System''' in the left navigation menu. |
| − | :*Click | + | :*Click '''Security''' in submenu. |
::Enter the following: | ::Enter the following: | ||
| Line 334: | Line 339: | ||
::*'''HTTP digest username''' | ::*'''HTTP digest username''' | ||
| − | :::Enter Auto Provisioning username. | + | :::Enter the Auto Provisioning username. |
::*'''HTTP digest password''' | ::*'''HTTP digest password''' | ||
| − | :::Enter Auto Provisioning password. | + | :::Enter the Auto Provisioning password. |
| − | ::*Click '''Set''' button. | + | ::*Click the '''Set''' button. |
| − | *Click | + | *Click '''Provisioning and configuration''' in the sub menu. |
| − | ::*In the '''Provisioning server''' field enter the following '''http://''' followed by '''Hostname''' or '''IP Address''' | + | ::*In the '''Provisioning server''' field, enter the following '''http://''' followed by '''Hostname''' or '''IP Address''' followed then by '''/prov'''. |
| − | ::::Example | + | ::::Example of a Hostname using HTTP: '''<nowiki>http://abc.bicomsystems.com/prov/%MACD.xml</nowiki>''' |
| − | ::::Example | + | ::::Example of an IP Address using HTTP: '''<nowiki>http://192.168.1.10/prov/%MACD.xml</nowiki>''' |
| − | *Click '''Set''' button. | + | *Click the '''Set''' button. |
| − | *Click | + | *Click the '''Start auto configuration''' button in the left navigation menu. |
| − | *You | + | *You will have to wait a couple of seconds for the configuration to be updated. <font color="red">'''NOTE:'''</font> Do not power off your phone. |
| − | *Auto provisioning process will start during phone reboot process | + | *The Auto provisioning process will start during the phone's reboot process. The phone will pick up an appropriate configuration file from PBXware. If everything is done as described above, you should have successfully registered your phone to PBXware. |
| + | |||
| + | Dial '''*123''' to verify registration. | ||
Latest revision as of 08:58, 12 June 2020
Introduction
This Configuration Guide is written as a general guide on how to configure the Gigaset phone model N870 to work with PBXware 5.3.5.
Requirements
Identifying Phone Model
To start and successfully complete registration of your Gigaset phone you need to know which phone model to set up.
On the back of each Gigaset phone, there is model information that you should check. Although various phone models can have exactly the same requirements and installation procedures, phone models can also have significantly different requirements and installation procedures, so that is why it is important to know the model you own which results in you setting up the device successfully.
Phone Firmware
- Make sure that your phone is loaded with an appropriate firmware version, 2.26.0.
- To find out the firmware version of your Gigaset phone model, open a new browser window and enter your phone IP address in order to access the phone's web administration interface login screen. Example: http://192.168.1.22.
- Log in to the phone's web administration interface with your username and password. Please note that the factory default username is admin and the factory default login password is admin.
DHCP Server
Fully configured and operational DHCP server.
PBXware Version
PBXware version 5.3.5.0
In order to find out the PBXware version:
- Log in to PBXware
- Navigate to Settings: About.
On the top of About page is a code similar to this one PBXware Edition: Business, Release: 5.3.5.0 (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v5.0 (62b7bcd), API: 5, libmemcached version: 1.0.18, where Release denotes the current version of your PBXware.
Installation
This section describes how to install and connect the phone to the electrical power and data network as well as how to apply factory settings.
The following topics are covered:
- Power Adapter
- Power over Ethernet (PoE)
- Factory Settings
Power Adapter
Connect the Network and Power
- Connect the DC plug on the power adapter to the DC port on the phone and connect the other end of the power adapter into an electrical power outlet.
- Connect the Ethernet cable between the Internet port on the phone and the network port on a router or switch to access LAN.
NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.
Power over Ethernet (PoE)
Connect the Network (only)
Using a regular Ethernet cable, your phone can be powered from a Power over Ethernet (PoE) compliant router or switch.
- Connect the Ethernet cable between the Internet port on the phone and an available port on the in-line power router or switch.
NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter. Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.
Find the Phone's IP address
Find out your Gigaset phone IP Address
- Open Menu on a dect phone
- Go to Settings
- Go to System
- Go to Local network
IP address should be displayed on the phone.
Reset to Factory Settings
This step is not required for brand new out-of-the-box phones, however, if the phone has been already used then it is a must.
- Disconnect the power supply.
- Power on the device while keeping the Connect button pressed and wait 15 seconds until the Connect button starts to blink fast.
- Release the Connect button and power off the device.
- Turn the device on again.
- Wait some time for a device to boot.
NOTE: Do not unplug or remove power to the phone while it is updating firmware and configuration.
Registering Phone
This section describes how to identify Gigaset phone model, requirements that must be met and how to register the phone by using Manual configuration or Auto provisioning.
The following topics are covered:
- Manual Configuration
- Auto Provisioning
Manual Configuration
This section describes how to set UAD settings, create the PBXware extension and register the phone.
The following topics are covered:
- UAD settings
- Creating Extension
- Registering Phone
UAD Settings
Log in to the PBXware's web administration interface
- Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: http://192.168.1.10.
- Log in to PBXware with your e-mail address and password.
UAD Settings
- Navigate to Settings: UAD.
- Make sure that the Grandstream UAD is enabled. To check the UAD status, click the Edit icon corresponding to your Grandstream phone.
- Make sure that Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.
- Click the Save button to save changes.
Creating Extension
Add the Extension
- Navigate to Extensions. Click the Add Extension button.
- The standard options window will be shown below.
- Select the Grandstream phone model from the UAD select box.
- Select Location: Local or Remote.
- Local is for all Extensions registered on the LAN and Remote is for all Extensions registered from remote networks, WAN, Internet etc.
- Click the Next step button.
Extension Values
- Enter values into the required field text boxes.
- REQUIRED FIELDS:
- Name
- Enter a name for the Extension being created. Example: John Smith.
- Enter the e-mail address associated with this Extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com
- Department
- Define the Department to which the Extension belongs to. Example: Sales.
- Click the Save button.
Registering Phone
This section describes how to register Gigaset phones using Hostname or IP Address.
Hostname or IP Address
Log in to the phone's web administration interface
- Open a new browser window and enter your phone IP address in order to access the phone's web administration interface login screen. Example: http://192.168.1.22
- Log in to the phone's web administration interface with your password. Please note that the factory default username is admin and the factory default login password is admin.
- Click the Settings tab at the top navigation menu.
- Click Telephony at the left navigation menu.
- Click the first Edit button.
- Click the Show advanced settings button.
- Enter or set the following details into the respective fields.
- REQUIRED FIELDS:
- Authentication name
- PBXware Extension number. Example: 1003
- Authentication password
- The Secret of the Extension as received in the e-mail associated with this Extension. Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created Extension.
- Username
- Same number as the Authentication name.
- Display name
- Usually the same number as the Authentication name.
- Domain
- PBXware IP address or domain name. Example: 192.168.10.1 or http://abc.bicomsystems.com
- Proxy server address
- Same as the Domain field.
- Registration server
- Same as the Domain field.
- Click the Set button.
- You will have to wait some time for a device to reboot. If everything is done as described above, you should have successfully registered your phone to PBXware.
Dial *123 to verify registration.
Auto Provisioning
This section describes how to set UAD settings, create the PBXware Extension, and register the phone using DHCP or Static IP address.
The following topics are covered:
- UAD Settings
- Creating Extension
- Registering Phone
UAD Settings
Log in to the PBXware's web administration interface.
- Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: http://192.168.1.10.
- Log in to PBXware with your e-mail address and password.
UAD Settings
- Navigate to Settings: UAD.
- Make sure that the Grandstream UAD is enabled. To check the UAD status, click the Edit icon corresponding to your Grandstream phone.
- Make sure that Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
- Click the Save button to save changes.
Creating Extension
Add the Extension
- Navigate to Extensions. Click the Add Extension button.
- The standard options window will be shown below.
- Select the Grandstream phone model from the UAD select box.
- Select Location: Local or Remote.
- Local is for all Extensions registered on the LAN and Remote is for all Extensions registered from remote networks, WAN, Internet etc.
- Click the Next step button.
Extension Values
- Enter values into the required field text boxes.
- REQUIRED FIELDS:
- Name
- Enter a name for the Extension being created. Example: John Smith.
- Enter the e-mail address associated with this Extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com
- Auto Provisioning
- Set to Yes.
- MAC Address
- Enter the Gigaset phone's MAC address. Example: 7C2F80123456. The MAC address can be found at the back of the phone.
- Click the Save button.
Registering Phone
This section describes how to register Gigaset phones using DHCP or HTTP.
The following topics are covered:
- DHCP
- HTTP
DHCP
Configure DHCP
- Make sure that your DHCP router is configured to use option 66 to automatically instruct phones with the URL for Auto provisioning. For more information, please refer to your router documentation or contact your network administrator.
Phone's first boot or user initiated reboot
- The Auto provisioning process will start during the phone's first boot or after the reboot process has been initiated by the user. The DHCP server will instruct the phone from where to pick up an appropriate configuration file. If everything is done as described above, you should have successfully registered your phone to PBXware.
Dial *123 to verify registration.
HTTP
- Open a new browser window and enter your phone IP address, e.g. http://192.168.1.22.
- Enter username and password and press the Confirm button. NOTE: The factory default username is admin and the factory default password is admin.
- Click the Settings tab.
- Click System in the left navigation menu.
- Click Security in submenu.
- Enter the following:
- HTTP digest username
- Enter the Auto Provisioning username.
- HTTP digest password
- Enter the Auto Provisioning password.
- Click the Set button.
- Click Provisioning and configuration in the sub menu.
- In the Provisioning server field, enter the following http:// followed by Hostname or IP Address followed then by /prov.
- Example of a Hostname using HTTP: http://abc.bicomsystems.com/prov/%MACD.xml
- Example of an IP Address using HTTP: http://192.168.1.10/prov/%MACD.xml
- Click the Set button.
- Click the Start auto configuration button in the left navigation menu.
- You will have to wait a couple of seconds for the configuration to be updated. NOTE: Do not power off your phone.
- The Auto provisioning process will start during the phone's reboot process. The phone will pick up an appropriate configuration file from PBXware. If everything is done as described above, you should have successfully registered your phone to PBXware.
Dial *123 to verify registration.
